Everyone knows that the maintenance of a car is very important, but when it comes to the maintenance of a certain part, we do not know what to do, and the maintenance of the chassis is easily overlooked. When faced with the chassis failure during the drive, everyone was overwhelmed. Here's to teach everyone how to conserve the chassis and how to rescue them in the event of a chassis failure in case of emergency.
Maintenance of the chassis is very important
Automobile maintenance experts say that it is important to maintain the chassis. Chassis cleaning and rust prevention must be done thoroughly to maintain the chassis. Thoroughly clean the chassis before anti-rust treatment. If there is too much mud in the chassis, wash it again with an oil-removing detergent to expose the chassis to the original “natural†color so that anti-rust care can begin. In a professional car beauty shop, the car can be lifted to a lifting rack for chassis cleaning, wiping, and rust prevention. It should be noted that after washing, be sure to wait until the water on the plate is completely dry before carrying out rust preventive care. When performing rust preventive care, the spray coating must be uniform so that the surface of the chassis forms a layer of durable, uniform anti-rust coating. After all of the work is completed, the air is dried naturally for 5 minutes to 10 minutes. The chassis rust treatment is completed.
After completing professional chassis care, it does not represent foolproof. Everyone has a misunderstanding that the car will be rinsed from time to time and will use detergents. At this time, please be careful not to use alkaline cleaners (especially washing powder, etc.) to wash the body and chassis, otherwise it will affect the anti-rust effect and Reduce rust-proof time.
Car care experts suggest that to go to a professional car beauty shop to do chassis care, there is a simple way to test the quality of its good or bad: after finishing the rust-proof nursing chassis, almost no water droplets are hung after high-pressure water jet washing. Only high-quality care can play a good rust protection effect.
Vehicle chassis damage first-aid
When the vehicle is damaged in the field or away from the vehicle repair location, the following emergency methods can be used to drive the vehicle to the place where there are vehicle repair conditions.
If the brake cylinder is leaking brake fluid or the branch pump line is broken, use tin and copper skin as a small mat at the branch of the branch pump, block the pipeline, and then tighten the screws; or flatten the fracture. ,Roll plugging, so that the wheel can not afford braking effect. Doing so may result in unilateral braking. Be careful when driving.
If the brake master cylinder lacks brake fluid, alcohol or spirits can be used instead. In special cases, fresh water can be used instead. If the brake cup swells, soak the swollen skin cup in hot water for 10 minutes to 20 minutes to remove the oily ingredients from the bowl so that the cup can be restored to its original size.
If the clutch friction lining slips, the friction lining that is less severely worn can be turned over. If it is seriously worn, use cotton cloth or several layers of canvas, and use steel wire or iron wire to pass through the hole in the steel sheet to fix it. When driving a vehicle, it should be done steadily and the shift action should be rapid.
If the tie rod ball section is broken, in the insurance (safety) bar or other place that does not affect the travel, remove a screw with a similar total ball joint length to replace the broken ball joint and install the knuckle arm and nut , The exposed part of the screw is riveted with a hammer. If the three-axle differential gear of the automobile is damaged, for example, if one of the middle and rear axle differentials is damaged, the axle and the axle of the axle can be removed and the vehicle can continue driving. If the front differential is damaged, the hub splint can be removed and continued.
China Wood Pellet Machine,Wood Pellet Mill supplier & manufacturer, offer low price, high quality Wood Pellet Making Machine,Wood Pellet Press, etc.To develop many models of products.For instance
Model Power(kw) Capacity(t/h)
XGJ460 55 0.5-0.8
XGJ560 132 1.5-2
XGJ720 160 2-3
XGJ850 220 2.5-3.5
Wood Pellet Machine
Wood Pellet Machine,Wood Pellet Mill,Wood Pellet Making Machine,Wood Pellet Press
Shandong Yulong Machine Co.,Ltd , http://www.yulong.cc